乐山tangibleConcrete mixing plantCompared with similar products on the market, the innovative HZS35 concrete mixing plant has many advantages: 1.In addition to the common sealing process, there are two steel bearing protective rings between the side mixing arm and the shaft head, which can prevent coarse sand from entering;2.The electric oil pump technology supplies oil vertically from four pump cores to four shaft heads, without diverting valves, reducing repair and maintenance costs;3.Concrete mixing plant图片Reducer reducer and oil seal system are designed and produced by well-known foreign manufacturers, longer service life, low noise, no oil leakage;4.Gear oil filtration/cooling system can be selected four generations of gear oil filtration and cooling system, military grade process, more durable。

Concrete mixing stations are becoming more and more common, and more and more people are using concrete mixers。However, many people do not know how to clean a concrete mixer。First, before using the concrete mixer, check that the controller is in good condition。Concrete mixing plant图片After shutdown, pour the water and stones into the mixing bucket for 10 to 15 minutes for cleaning, and then remove the water and stones。When the operator needs to enter the mixing cylinder for cleaning, in addition to cutting off the power, remove the fuse, but also need to lock the switch box。Secondly, the concrete mixer should be regularly maintained, such as cleaning, lubrication, refueling and so on。Third, we must remember that the accumulation of concrete in the concrete mixing drum cannot be removed by hammering。We had to chisel it out。Fourth, winter usetangibleConcrete mixing plant图片Pay attention to cleaning the drum of the concrete mixer with water after the end of the work, and drain the water in the pump, water tank and water pipe to avoid frostbite of the pump, water tank and water pipe。

First of all, when choosing a concrete mixer, we must make it clear that choosing a good one does not just mean that the material is good and the price is expensive。As the saying goes, what suits you is the best, and the blender is no exception。1, the difference of mixer materials For the mixer of this type, model diversification of the machine, choose to suit their own is undoubtedly a big problem。Therefore, when choosing a blender, we must first confirm the difference between blender materials, some of which are dry powdertangibleConcrete mixing plant图片Some of them are liquidConcrete mixing plant图片There are also solid-liquid mixtures, so as long as the difference between materials is determined, the scope of application can be reduced。2, the speed of the mixer is followed by the mixing speed of the mixer, the natural production efficiency of the fast mixing speed is high, and the slow mixing speed will naturally affect the progress of the construction。3, the difference between any mixer and its mixer accessories will have inaccessible corners, commonly known as dead corners, so choosing a small percentage of dead corners will greatly improve the production efficiency of its machine。

Concrete mixing station can not be immediately left after work 1.tangibleConcrete mixing plant图片After the work is completed, the residual water and additive in the pump, additive pump, water tank, additive tank, water and additive pipeline should be drained to prevent damage to the pump and its pipeline, and start the additive pump of the pump to run for 1-2 minutes。2.Clear the ash accumulation inside and outside the wall of the mixing tank, the concrete residue on the discharge port, the mixing shaft and the discharge door, wash these centers with water, and if necessary, put in a small amount of stones and water to stir for a few minutes before releasing。Clean vehicle, additive tank and supply system with water。3.The smooth points are located in the discharge door shaft of the mixer, the door shaft of the storage hopper and the weighing hopper, the belt conveyor, the machine support wheel, the press wheel, the roller, the bearing, the transmission chain, the upper and lower end bearings of the spiral shaft and the main machine gear。4.tangibleConcrete mixing plant图片Check the wear condition of blades, scrapers, mixing arms, etc. Adjust the clearance or change it if necessary;Vibrator coupling bolt is loose or not;Check contactors in electrical appliances;Whether the static contact of the intermediate relay can be damaged and burned。

Select mixing plant site need to pay attention to what points？1.Construction of mixing plant should choose a flat, wide, away from residential areas。If the hillside terrain can be fully utilized and the material field is set on the higher ground plane of the hillside, the loading height of the batching machine can be reduced, so that the climbing Angle on the loader is small or no climbing.tangibleConcrete mixing plant图片It saves energy and reduces wear。2 Convenient transportation (for tank trucks, pump trucks, cement trucks, etc.) 3.It should be built next to the material yard. The distance between the material yard and the sand plant should be close to ensure that the water supply is sufficient。According to the existing natural landform of the mixing station site, the production area and living area of the mixing station can be divided into two independent areas, the size of the available site in the living area is 36M×70M, and the production area of the mixing station is a rectangle.tangibleConcrete mixing plant图片The site is basically flat and in place。But to consider the ground drainage, so that there is no water phenomenon。